ELECTRONIC INTEGRATED SYSTEMS MECHANIC

Summary

IOWA ARMY NATIONAL GUARD - TITLE 32 EXCEPTED SERVICE POSITION This position is restricted to current Military members of the Iowa Army National Guard. LOCATION: AASF 1, Boone, IA

Duties

As a ELECTRONIC INTEGRATED SYSTEMS MECHANIC, WG-2610-12 your duties are below. Performs operational checks, inspections, tests and troubleshooting on electronic integrated systems composed of a number of sensor subsystems: Integrated Vehicle Health Management System (IVHMS), the Common Missile Warning System (CMWS), the Improved Countermeasure Dispenser System (ICMD), the Night Vision Goggle System (NVG), the Air Data Subsystem, the Attitude Heading Reference System (AHRS) and Doppler/GPS Navigation System (DGNS), Command Instrument Set (CIS) ; a logic subsystem-- the Multiplex Data Bus System (MUX), the Multiplex Remote Terminal Units (MRTU), Data Link Terminal Units (DLTU), and Digital Automatic Flight Control System (DAFCS); and actuating subsystems--, and the Digital Automatic Stabilization System (DASS), which includes the Stability Augmentation System (SAS) and Command Augmentation System (CAS) and Hover Augmentation System (HAS). Completes operational checks, inspections, tests and troubleshooting of Line Replaceable Units (LRU). Isolates unusual malfunctions using technical manuals, schematics, and wiring diagrams, tools and test equipment including automatic test equipment. Solves problems by analyzing installation, circuitry, and operating characteristics of the systems. Adjusts and aligns sensors, transmitters, amplifiers, power supplies, display devices, controls, actuators, servos, computers and other related components. Removes faulty LRUs for shop repair. Installs serviceable components into aircraft and performs total systems alignments in accordance with existing technical manuals and directives. Accomplishes technical manual compliance and modification of components and systems and completes systems checkout for proper operation. Maintains, modifies, calibrates and inspects a wide variety of user test, measurement, and diagnostic equipment (TMDE). Completes bench check, testing, repair, inspection, modification, programming, reprogramming, mating, adjusting, alignment, and analyzing of LRUs and shop replaceable units. Uses a variety of test equipment such as automatic test equipment (ATE), oscilloscopes, DTA computer, multi-meters, power-meters, and special purpose bench test sets. Tests and troubleshoots solid state electronic assemblies and subassemblies such as circuit cards, modules, rate gyros, electronic control amplifiers, electro-mechanical assemblies, random access memories, programmable read-only memories and various integrated circuits. Identifies faulty parts and repairs to level authorized. Ensures and certifies operational integrity of various night vision systems, and electro-optical components. Reassembles unit after repair, performs alignment and makes shop checks. Recommends methods to improve equipment performance, technical data, and maintenance procedures by reporting hardware and software malfunctions, initiates material deficiency reports both on equipment and in technical data, and assists in design changes as necessary. Conducts debriefing of aircrews to determine the nature of system malfunctions, then documents all maintenance performed and records information related to the system, LRU's, or shop repairable units on both aircraft and historical records. When designated on NGB Flying Status Orders, serves as member of flight crew for the purpose of diagnosing and recording malfunctions, or otherwise determining maintenance and repair requirements. Guides lower level mechanics in the performance of duties. Conducts on-the-job training on assigned systems and related support equipment and tasks to include classroom instruction as necessary. Processes and accounts for due-in supply assets. Ensures that material and equipment are properly stored, protected and maintained and that funds are not obligated for material or parts without proper justification. Prepares for and participates in various types of readiness evaluations such as Operational Readiness Evaluations (ORE), Command Logistics Readiness Inspections (CLRT-X), and Aviation Resource Management Surveys. May be required to perform additional duties such as structural firefighting, aircraft handling, heavy equipment operation, and maintenance of facilities and equipment, or serve as a member of a team to cope with natural disasters or civil emergencies. Complies with safety, fire, security, and housekeeping regulations. Performs other duties as assigned. D0872P01

Requirements

NATIONAL GUARD MEMBERSHIP IS REQUIRED: This is an excepted position that requires military membership in a compatible military assignment in the Iowa Army National Guard. Selectee will be required to wear the military uniform. Acceptance of this excepted position constitutes concurrence with these requirements as a condition of employment. APPLICATION MATERIALS MUST BE RECEIVED BY 09/25/2026 . FAILURE TO PROVIDE COMPLETE INFORMATION MAY RESULT IN YOUR NOT RECEIVING CONSIDERATION FOR THIS POSITION. Please refer to the Qualifications and Evaluations Section of this Announcement to understand the qualification requirements, and the How to Apply Section for detailed instruction on applying. TRIAL PERIOD REQUIREMENT: As a condition of employment for accepting this position, you will be required to serve a 2-year trial period or 1-year (Veterans Preference Eligibles Only) during which we will evaluate your fitness and whether your continued employment advances the public interest. In determining if your employment advances the public interest, we may consider: Your performance and conduct. The needs and interests of the agency. Whether your continued employment would advance organizational goals of the agency or the Government; and Whether your continued employment would advance the efficiency of the Federal service. Upon completion of your trial period your employment will be terminated unless you receive certification, in writing, that your continued employment advances the public interest. SECURITY CLEARANCE REQUIREMENT: Employment is subject to attaining and maintaining a clearance as required by this position. If the selectee does not possess the applicable security clearance when hired, application must be made within 30 days of the start date. Failure to make application for the required security clearance will result in termination of employment. Failure to complete prescribed courses may be cause for reassignment or termination of FTS. Military Rank Requirements: WARRANT OFFICERS AND ENLISTED MEMBERS (CW2 to E-4)

Qualifications and evaluation

Once the announcement has closed, your resume and supporting documentation will be used to determine if you meet the qualifications listed on this announcement. If you are found to be among the qualified candidates, you will be referred to the selecting official for employment consideration. Verbiage displayed on your resume or application must contain your own words. You may refer to position descriptions, i.e. the general and specialized experience located within the vacancy announcement, to assist with describing work experiences; however, resumes or applications received in verbatim will not be considered. In your resume you will need to address the general and specialized experience listed above. Please use as much detail as needed, giving dates (months and years) of the experience, position title and how the experience was gained. This information is needed to determine if you are qualified for the position. Knowledge, Skills and Abilities required for this position: Ability to apply electronic theories and practices to identify, isolate and repair malfunctions in one or more complex integrated systems where knowledge of the entire system is necessary to interpret error data and trace back through a number of units of the system to locate deficiencies. Thorough knowledge of the principles of digital and analog circuits, electro-mechanical devices, solid state devices theory, digital techniques, synchro/servo operation and integrated circuit theory. Ability to interpret and trace schematic, logic and wiring diagrams and use a wide variety of test, measurement, and diagnostic equipment (TMDE). Ability to perform algebraic and trigonometric formulas to solve work-related problems. Current certification in high reliability soldering techniques, as well as electrostatic discharge protective techniques. Knowledge of the Army Maintenance Management System (TAMMS) and other automated programs, publications or directives as may be applicable to the function.

How to apply

To apply for this position, you must complete the online application and submit the documentation specified in the Required Documents section below. A complete application package must be submitted by 11:59 PM (EST) on the closing date of the announcement to receive consideration. To begin, click Apply to access the online application. You will need to be logged into your USAJOBS account to apply. If you do not have a USAJOBS account, you will need to create one before beginning the application. Follow the prompts to select your resume and/or other supporting documents to be included with your application package. You will have the opportunity to upload additional documents to include in your application before it is submitted. Your uploaded documents may take several hours to clear the virus scan process. After acknowledging you have reviewed your application package, complete the Include Personal Information section as you deem appropriate and click to continue with the application process. You will be taken to the online application which you must complete in order to apply for the position. Complete the online application, verify the required documentation is included with your application package, and submit the application. To verify the status of your application, log into your USAJOBS account (https://my.usajobs.gov/Account/Login), all of your applications will appear on the Welcome screen. The Application Status will appear along with the date your application was last updated. For information on what each Application Status means, visit: https://www.usajobs.gov/Help/how-to/application/status/.

Required documents

To apply for this position, you must submit a complete Application Package which includes: Your resume showing work schedule, hours worked per week, dates (format should include Month and Year) of employment and duties performed. Additional Supporting Documents (if applicable): Cover Letter, Transcripts, DD 214, SF-50, ect.

Additional information

ENLISTMENT CASH BONUSES: Acceptance of a technician position may affect any bonus and/or educational assistance that may be applicable. Please contact your Education Office prior to accepting a position with the Iowa Army National Guard. Participation in direct deposit is mandatory. If you are a male applicant born after 12/31/1959 and are required to register under the Military Selective Service Act, the Defense Authorization Act of 1986 requires that you are not eligible for appointment in this agency (https://www.sss.gov/RegVer/wfRegistration.aspx).